next up previous contents
suivant: Bibliographie monter: Développement d'un système d'exploitation précédent: Description des outils   Table des matières

Sous-sections

Configuration des ports du Palm m500

Ces informations sont tirées des sources de l'émulateur POSE 3.5.

Port B

Bit Fonction
0 (L) USB Chip Select #
1 (L) SDRAM Control - SDWE#
2 (L) SDRAM Control - SDRAS#
3 (L) SDRAM Control - SDCAS#
4 (L) SDRAM Control - SDCS#
5 (L) Radio in-service signal
6 (L) Alarm LED (= 1 -> LED ON)
7 (P) Unfiltered Sound PWM

Port C

Bit Fonction
0 (L) Mono LCD Data Bit 0
1 (L) Mono LCD Data Bit 1
2 (L) Mono LCD Data Bit 2
3 (L) Mono LCD Data Bit 3
4 (L) Mono LCD Frame Pulse
5 (L) Mono LCD Line Pulse
6 (L) Mono LCD CLK
7 (L) Enable the LCD controller

Port D

Bit Fonction
0 (H) Keyboard Column 0 (aka INT0)
1 (H) Keyboard Column 1 (aka INT1)
2 (H) Keyboard Column 2 (aka INT2)
3 (H) Keyboard Column 3 (aka INT3)
4 (L) HotSync/Dock Button (aka IRQ1)
5 (-) SPI #1, slot , SD/MMC Card Detect E0R
  Wake EOR Ready (aka IRQ2)
6 (L) USB Interrupt (aka IRQ3)
7 (L) Power Fail interrupt (aka IRQ6)

Port E

Bit Fonction
0 (L) SPI TXD
1 (L) SPI RXD
2 (L) SPI Clock
3 (L) Radio ready (XDR on radio)
4 (H) RXD1# (used by Radio)
5 (H) TXD1# (used by Radio)
6 (L) RTS1#
7 (L) CTS1#

Port F

Bit Fonction
0 (P) LCD Contrast
1 (L) Pen Interrupt, Pen IO (IRQ5)
2 (-) Free (CLKO)
3 (P) A20
4 (P) A21
5 (-) A22
6 (L) DTR to radio (XER on radio)
7 (L) Mass ROM chip select

Port G

Bit Fonction
0 (L) LCD VCC control
1 (L) EL_ON (= 1 -> LCD BackLight ON)
2 (L) ADC_CS# (old ID_DETECT#)
3 (L) 232_SHDN# = 1 -> Serial port ON for UART 1
4 (H) USB_SPND
5 (H) ADC_CS#
6 (-) Unused6
7 (-) Unused6

Port J

Bit Fonction
0 (L) Radio RSSI 3
1 (L) Radio RSSI 2
2 (L) Radio RSSI 1
3 (L) Radio Power State
4 (L) RXD2#
5 (L) TXD2#
6 (L) RTS2#
7 (L) CTS2#

Port K

Bit Fonction
0 (L) Radio power on/off
1 (-) LCD_DISP_ON (RW#) (= 1 -> LCD ON)
2 (-) AC_PWR# (LDS#)
  (old (L) Charging Enable)
3 (-) Free 3
4 (-) VIBE_EN (= 1 -> vibrator ON)
  (Old (L) Radio Carrier Detect)
5 (H) Keyboard Row 0
6 (H) Keyboard Row 1
7 (H) Keyboard Row 2

Port M

Bit Fonction
0 (-) SDCLK
1 (-) SDCE
2 (-) SDDQMH
3 (-) SDDQML
4 (-) SDA10
5 (L) Infrared Shut-down (UART 2) (= 1 -> port IrDa OFF)
  (L) Voltage Translator shutdown (UART 2)
6 (-) Unused6
7 (-) Unused7


next up previous contents
suivant: Bibliographie monter: Développement d'un système d'exploitation précédent: Description des outils   Table des matières
Fabian Skivee 2002-06-04